Optimizing your Wi-Fi network

The top of the fireplace in the living room is a good spot to leave your Wi-Fi router for best coverage.

There are a few ways to make sure you get the best out of your Wi-Fi network. With some, you just need to do a little bit of tweaking; with others, depending on your home, you might need to get extra equipment.

Let's start with the ways that probably won't cost you anything, other than a little bit of time.

1. Placement
Location: This globe, however, is not exactly spherical; one of the reasons is because the signals are generally turned to go out more horizontally than vertically and like all radio signals, they tend to spread laterally and downward the farther they are from the broadcaster.A wireless router (from here on in this post, it will be addressed as "router" for short) broadcasts Wi-Fi signals away from it in all directions.Think of the signal coverage as a globe with the router being right in the center.

To take advantage of this, use the telephone jack (or coax cable outlet) at or near the center of the house, preferably on the upper floor when applicable, to connect to your modem and then your router..

Surroundings: Since it's not possible to have that indoors, you can improve the signal a great deal by making sure the immediate surroundings of the router/modem are clear, especially in the directions you want the signals to reach.The best place to leave the router is in midair, but since that's quite hard to do, the second best thing is to put it on the surface of a desk, or mount it on the wall when applicable.

Antenna positioning: Generally you want the antennas to stay vertical if you want the signal to go wide (which is the most popular usage). If want the signal to go deep into the basement and up to the top floor, set the antennas to stay horizontal. With a router that comes with external antennas, you can slightly tweak the above-mentioned globe of coverage. Note that this only works relatively, and with some routers, you might not experience any difference at all whichever way you set its antennas.

 2. Equipment
Now that you have placed your router properly and still don't find enough improvement, it's time to check the equipment. Get ready to spend some money.

Router: Ideally you just want to have one wireless broadcaster at home and for most homes, a single router is good enough. That said, if you have a small house and the router (put in the middle) can't cover every corner, it's time to consider replacing it.

Many wireless router can also work as an access point. In this case its WAN port is used like a LAN port.

Access point: A separate access point is an ideal solution for a large and sprawling home, one that you can't put the router in the center, or one with a deep basement, with an existing router. Basically, you want to put the second access point at the location where the signal of the existing router can't reach or gets really weak.

Now the trick is to connect the access point to the router. Ideally, you want to run a network cable from the router to the access point (you want to connect the access point's LAN port to one of the router's LAN ports). If this is too much of a job, you can resort to power-line networking.

Power line: A power-line adapter basically turns your home's electrical wiring into network cables. In the case of the separate access point scenario above, you can use a pair of power-line adapters, such as the D-Link DHP-510AV. Connect one of the adapters to the router and the other to the access point, using network cables. After that, if you want to make your home network seamless, name the Wi-Fi network (or SSID) of the access point the same as that of the existing router. In this case, make sure you use the same security settings (encryption key, method, and so on). Or you can also keep them as two separate Wi-Fi networks for easy management.

There are also power-line adapter kits with a built-in access point, called power-line range extenders, such as the Netgear XAVNB2001. In this case, you don't need to get the second access point/router.

In addition to power line, you can also opt for a pair of MoCA adapters. MoCA stands for Multimedia over Coax Alliance, and similar to power line, turns coax cables (those used by cable TV) into network cables. MoCA adapters are great solutions for homes with multiple cable outlets in different rooms.

Range extender/repeater: These are wireless devices that can connect to an existing Wi-Fi network and then rebroadcast that same network's signal farther. Most of these devices support Wi-Fi Protected Setup and can connect to the existing router with the push of a button; after that, you can just put one at the edge of the existing network's Wi-Fi range and have that range increased.

I am not a fan of this type of device because of a few reasons:

First, it's hard to gauge their effectiveness; you need to put a range extender/repeater relatively close to the existing router for it to have a good connection with the main network, but at the same time far enough for it to really extend the range. It's very hard to find the sweet spot for it to be effective both in terms of range and connection quality.

Second, the repeater basically duplicates the existing Wi-Fi network with one of its own, and as mentioned above, Wi-Fi signals are broadcast in all directions. This means devices in the area where the two networks overlap have to deal with interference and signal saturation. This is especially bad for the 2.4Ghz band.

That said, a range extender/repeater is still the fastest way to relatively extend a Wi-Fi network's coverage.

You can easily find out a home network router's IP address by running the ipconfig command from any connected computer.

3. Settings
One of the problems with Wi-Fi networks is the risk of losing your bandwidth to unauthorized users. This part helps you secure your network and optimize it for speed. Note that it's slightly more advanced and might seem intimidating to novice users. But you will be a novice no more if you go through with it. This part is only recommended for those interested in learning more about networking.

With the exception of networking products from Apple, most, if not all, other routers and access points on the market comes with a Web interface. This means that from a connected computer, you can open up the router's management Web page by going to its IP address. Unless you have changed it, the default IP address is generally printed on the bottom of the router, or on its user guide, and tends to be in this format: 192.168.x.1.

It's easy to find out your router's IP address; here are the common steps to get to any home network's router's Web interface:

Step 1: From a connected computer (running Windows Vista or 7), click on Start button, type "cmd" in the search area, then press Enter. (If you use Windows XP, you can navigate the Start Menu and run the Command Prompt item.)

Step 2: Now in the black command prompt window, type in "ipconfig," then press Enter. You will see lots of information displayed in the window. Find the string of number after Default Gateway, that's the router's IP address.

Step 3: Type that IP address in the address bar of a browser, such as Firefox, and press Enter; now you are at the router's Web interface. You will have to log in with an account. The username is almost always admin; for the password, check the router's manual or ask the person who first set up the network for you.

The Web interface offers a convenient and extensive way to manage a router's or access point's settings.

On the Web interface, the following wireless settings will help your network stay safe:

Network name and password: Most if not all routers come with a default Wi-Fi network name (or SSID) and password; you won't want to use those. This is mostly because that reveals to advanced users which router you have and that, well, you don't know much about networking. Changing the SSID and password to your liking also helps you remember them better.

Hide your SSID: By default all routers broadcast the Wi-Fi network name. This makes it convenient since clients can "see" them. Hiding the SSID makes your Wi-Fi network invisible to others. The only drawback is that you have to manually type it in when you want to connect a new client to it. There's a trick for it: turn the SSID on briefly when you want to connect a new client, once that's done, hide it again.

Use WPA 2: Using the WPA 2 encryption method helps both increase the security and the speed of the Wi-Fi signal. The only catch is that WPA 2 might not be compatible with older clients. Most new clients released in the past few years support WPA 2, however. You can try using WPA 2 first and if some of your clients are unable to connect, switch it back to WPA.

In addition, once you have accessed the router's Web interface, there are many other settings that you can try. For safety, there are also MAC address filters, Internet filtering, and so on. Note that a router generally takes about a minute to restart to apply new settings.

That's it for now; if you have more questions, put them in the comment section below or send it us way via e-mail or at us Facebook page.

PakarPC No 23-1, Block A, No 2 Jalan Langkawi 53300 Setapak Kuala Lumpur FB:facebook.com/thepakarpc Hotline:1800-88-7508

Categories: